How To Clean Kitchen Splashbacks

If cleaning kitchen splashbacks is too much of a chore, keep reading. In this post, we’ve categorized the most successful techniques for cleaning each type of splashback. For installers like us, kitchen waterproofing is no issue. We provide clear instructions for any cooking scenario, whether it’s water-damaged tiles, stainless steel, or acrylic splashbacks.

Cleaning acrylic splashbacks

Acrylic is a flexible, yet fragile and soft material. This implies that you must exercise caution when cleaning splash backs for kitchens made of acrylic. If you’re using a rough cloth, be cautious since it may scratch the glossy surface. Keep in mind that scuffs are simple to remove if they appear. It’s also possible to polish them with a fine-toothed comb, as the maker will show you.

1. Wipe the splashback clean with a clean, gentle cloth to remove any dirt or grime.
2. Instead of using a harsh chemical, use a mild household cleanser to remove oily residues.
3. Last but not least, use a dry cloth to clean the splashback for a perfectly polished look.

To make things easier for you, remove stains as soon as they appear. It will be more difficult to clean if they are left for a long time.

Acrylic splashbacks need to be maintained on a regular basis. Check for fractures and repairs as soon as possible at the margins. If you find any problems, correct them right away with an appropriate silicone sealer. Every 5 years, you must use a special sealer to cover the whole surface.

Cleaning glass splashbacks

To keep your glass splashback looking new, use a high-quality, non-abrasive glass cleaning solution. If you want to perform it yourself, feel free to use a DIY cleanser instead.

1. The ideal ratio is one part vinegar to four parts water.
2. A clean spray bottle should be applied to the entire surface.
3. It’s a straightforward process that may be finished in a matter of minutes. Clean the glass with a soft microfiber cloth. Lint-free fabrics are the ideal option for cleaning windows.

Streaking is a typical concern when it comes to cleaning glass. While you work so hard to create a spotless surface, the fast-drying solution will leave streaks. To avoid streaks, clean away from direct sunlight. You can also prevent streaking by using newspapers. To avoid staining your skin, make sure to use gloves.

If the water problems persist, use distilled water when preparing your DIY cleaning solution. The tap water contains minerals that cause unsightly streaks on clean surfaces.

Cleaning stainless steel splashbacks

A simple DIY cleaning solution can clean stainless steel kitchen splashbacks quickly. You’ll need three things:

The materials needed are clean and empty spray bottle, unscented vinegar, and olive oil.

1. In a spray bottle, combine the vinegar and spritz it on your stainless steel splashback.
2. Wipe the surface clean with a dry cloth to remove any greasy residues. The stainless steel’s distinctive sheen will be restored.
3. After you’re finished, use a microfiber cloth or paper towels to apply a little bit of olive oil. This method will increase the gleaming and polished surface, making it appear new. The amount should be kept to a bare minimum. Otherwise, the splashback will look greasy.

However, keep in mind that stains requiring more attention must be addressed one at a time. If the discolouration is dry, try using a paste of water and baking soda to tackle it. Apply the paste to the discolouration and leave it for half an hour before cleaning with a dry cloth drop event.

If all else fails, a combination of equal portions of water and vinegar may be used to remove entrenched stains. Apply it directly to the stain, wait a few minutes, then clean with a clean towel.

Remember the do and don’ts when cleaning splashbacks

• To avoid stains from being absorbed, use a solution of 3 parts water to 1 part bleach.
• Using a clean, lint-free cloth is advised to prevent scratches.
• The sealing layer might be damaged by various chemicals. Make sure you’re using the ones your supplier recommends.
• Examine the splashback’s edges for any cracks or repairs that need to be addressed.